LoraWAN TTN http data to gsheet


this one work, and can parsing field data with json, it first has to run setup. 

also change your payload based on the data field. The problem I met is that the decode data is not shown, same as the down link url

https://blog.squix.org/2017/07/thethingsnetwork-how-to-use-google-spreadsheet-to-log-data.html



this one is another version originated form above.: https://github.com/Uspizig/Ttn-gooogle-script

Nice one:

https://github.com/avbentem/libelium-waspmote-lorawan is a well documented project, there is a section of http to google sheet and run on latest V8 runtime of google app script.https://github.com/avbentem/libelium-waspmote-lorawan/blob/master/src/google-sheets/README.md

the code will send email to sheet owner in case of any error. So make sure you adjust the field property correctly. 


After modification of  row.push fields. part, it works pretty well.

my little question is that since few days, my sensor node always resend 3-4 times as retry. I will look into this.


For these http post to google sheet,the worry is that it seems google doesn't like this integration it show :

Go into the small advanced

and select the last line marked with unsafe then it would work.





Other possibility

https://github.com/alvarowolfx/gcloud-lora-ttn

https://www.hackster.io/fabiocaputo996/google-cloud-based-iot-system-lorawan-ttn-mqtt-4378a4




留言

張貼留言

這個網誌中的熱門文章

Heltec ESP32+OLED+Lora, hardware testing

圖片
you can easily find some good boards from china, but most of them lack of accurate document... Hrere is an example; https://hackaday.io/project/26991-esp32-board-wifi-lora-32 the board looks good with lora and a 128x64 OLED, but the IIC and reset connection is important, since pin can be muxing easily, so every board could be different. pinMode(16,OUTPUT);  digitalWrite(16, LOW); // set GPIO16 low to reset OLED  delay(50);  digitalWrite(16, HIGH); // while OLED is running, must set GPIO16 to high  and, if needed, edit your Wire.begin() to Wire.begin(4,15); (4 = SDA 15 SCL)  i tested it with the Adafruit SSD1306 and the Acrobotics SSD1306 Librarys  both work.  Display size is 128x64 There are discussions on these boards on TＴＮ as a LORA node..or maybee single ch gateway? Heltec has a git :  https://github.com/Heltec-Aaron-Lee And there is another copy call TTGO https://de.aliexpress.com/item/TTGO-LORA32-868-915-Mhz-SX1276-ESP32-Oled-display-Bluetooth-WIFI
閱讀完整內容

micro SD card for ESP32, on lolin32 with OLED and heltec 32 lora oled

圖片
I have purchased 2 micro SD card holder for my esp project. First I would like to test with heltec esp32 lora oled module. this module uses: sck=05 MISO=19 MOSI=27 SS(lora)=18, then I assigned 21 for sd SS and there is a lib in esp32-arduino, which use SS default at 5 I took the example and use SD.begin(21), but I alway get the error: entry 0x40078a9c Card Mount Failed But I do saw once that it read out the sd card type and volume. Not sure it's the issue of lora sd card swithing, or it just can't work. The other esp32 card I have is an wemos esp32 oled, it did not leave me too much pins, I need to find out how to connect sd to it. But I have wemos D1 mini esp8266 on hand, and connect it as:  * The WeMos Micro SD Shield uses:  * D5, D6, D7, D8, 3V3 and G  *  * The shield uses SPI bus pins:  * D5 = CLK  * D6 = MISO  * D7 = MOSI  * D8 = CS It's not working with the example in the arduino IDE 1.8.5, which marked SD(esp8266), but it w
閱讀完整內容

Install Network Time Protocol(NTP) on BeagleBone with Angstrom linux and set local time zone

Referenced from : http://cwraig.id.au/?p=513 1. Update your Package List opkg update 2. Get the ntp Package opkg install ntp ntpdate Update 2014/07/03 for the latest beaglebone image(2013-06-20) with kernel 3.8.12, after this installation,  system will add to service list, so only need to change time zone 3. Now we need to stop the ntpd service so we can request a manual update /etc/init.d/ntpd stop manual update ntpdate pool.ntp.org type in date, you should see the date is changing to current date and time, but the time zone is not corrected. The time zone info is contained in /etc/localtime , use this to remove it: rm /etc/localtime before link up our time zone, look into /usr/share/zoneinfo folder for your timezone. I did not find taiwan in asia, not plan to use hong_kong, but there is still: /usr/share/zoneinfo/Etc/GMT-8 now we make the link with ln command ln -s /usr/share/zoneinfo/Etc/GMT-8 /etc/localtime now type date again to check, should ha
閱讀完整內容