Linaro = Creating your own image =

每次linaro 每次上都會說：

Install instructions

There are two methods to install linaro builds:
using pre-built image
creating your own image with linaro image tools

這次打算用 android 4.0 for pandaboard 1207來試試....
linaro image tools....

http://releases.linaro.org/12.07/android/leb-panda/

這一堆是拿來 down load files...terminal 裡照著打都沒事,網路正常就會抓...
$ wget http://releases.linaro.org/12.07/android/images/panda-ics-gcc47-tilt-tracking-blob/boot.tar.bz2 http://releases.linaro.org/12.07/android/images/panda-ics-gcc47-tilt-tracking-blob/system.tar.bz2 http://releases.linaro.org/12.07/android/images/panda-ics-gcc47-tilt-tracking-blob/userdata.tar.bz2

安裝：linaro image tools

說方法有兩種, 我只會第一種....一樣在terminal裡打....

$ sudo add-apt-repository ppa:linaro-maintainers/tools
$ sudo apt-get update
$ sudo apt-get install linaro-image-tools

也會裝完....

再來放進去SD CARD,看看是哪一個device,我的是 /dev/sdb, 照著打....

sudo linaro-android-media-create --mmc /dev/sdb --dev panda --system system.tar.bz2 --boot boot.tar.bz2 --userdata userdata.tar.bz2

這下機車了....跑了個error....
ImportError: No module named yaml

google了一下, 這個yaml雖然是python的一部分, 不過似乎是要另外裝的....

key這行：
sudo apt-get install build-essential python-yaml cmake subversion wget python-setuptools mercurial git-core

有人還會加上 python-pip, 像這樣：
sudo apt-get install build-essential python-yaml cmake subversion wget python-setuptools mercurial git-core python-pip

這樣又跑了一會....裝好後再試....

sudo linaro-android-media-create --mmc /dev/sdb --dev panda --system system.tar.bz2 --boot boot.tar.bz2 --userdata userdata.tar.bz2

終於等到這行....

Done creating Linaro Android image on /dev/sdb









留言

張貼留言

這個網誌中的熱門文章

Heltec ESP32+OLED+Lora, hardware testing

圖片
you can easily find some good boards from china, but most of them lack of accurate document... Hrere is an example; https://hackaday.io/project/26991-esp32-board-wifi-lora-32 the board looks good with lora and a 128x64 OLED, but the IIC and reset connection is important, since pin can be muxing easily, so every board could be different. pinMode(16,OUTPUT);  digitalWrite(16, LOW); // set GPIO16 low to reset OLED  delay(50);  digitalWrite(16, HIGH); // while OLED is running, must set GPIO16 to high  and, if needed, edit your Wire.begin() to Wire.begin(4,15); (4 = SDA 15 SCL)  i tested it with the Adafruit SSD1306 and the Acrobotics SSD1306 Librarys  both work.  Display size is 128x64 There are discussions on these boards on TＴＮ as a LORA node..or maybee single ch gateway? Heltec has a git :  https://github.com/Heltec-Aaron-Lee And there is another copy call TTGO https://de.aliexpress.com/item/TTGO-LORA32-868-915-Mhz-S...
閱讀完整內容

micro SD card for ESP32, on lolin32 with OLED and heltec 32 lora oled

圖片
I have purchased 2 micro SD card holder for my esp project. First I would like to test with heltec esp32 lora oled module. this module uses: sck=05 MISO=19 MOSI=27 SS(lora)=18, then I assigned 21 for sd SS and there is a lib in esp32-arduino, which use SS default at 5 I took the example and use SD.begin(21), but I alway get the error: entry 0x40078a9c Card Mount Failed But I do saw once that it read out the sd card type and volume. Not sure it's the issue of lora sd card swithing, or it just can't work. The other esp32 card I have is an wemos esp32 oled, it did not leave me too much pins, I need to find out how to connect sd to it. But I have wemos D1 mini esp8266 on hand, and connect it as:  * The WeMos Micro SD Shield uses:  * D5, D6, D7, D8, 3V3 and G  *  * The shield uses SPI bus pins:  * D5 = CLK  * D6 = MISO  * D7 = MOSI  * D8 = CS It's not working with the example in the arduino IDE 1.8.5, which m...
閱讀完整內容

AIS0. understanding AIS NMEA 0183: How it's coded

For my boat tracking system, I found out that using AIS format seems to be a good idea, at least I don't have to worry about how to present boat data, since there are already plenty things for do this on mobile phone or PC. Here is what I read: http://catb.org/gpsd/AIVDM.html Looking into AIS NMEA0183, it has much more application then I think. Such as MOB device, epir, aid to navigation device...etc, all are included. it use the first few char to indicate the function: Table 1. AIS talker IDs !AB NMEA 4.0 Base AIS station !AD MMEA 4.0 Dependent AIS Base Station !AI Mobile AIS station !AN NMEA 4.0 Aid to Navigation AIS station !AR NMEA 4.0 AIS Receiving Station !AS NMEA 4.0 Limited Base Station !AT NMEA 4.0 AIS Transmitting Station !AX NMEA 4.0 Repeater AIS station !BS Base AIS station (deprecated in NMEA 4.0) !SA NMEA 4.0 Physical Shore AIS Station It can also be used between device on boat for message communication, AIVDO The...
閱讀完整內容