救回我的i9000聯絡人

想刷 ics 4.0, 先用了samsung KIES來把資料都備份起來, 好不容易裝起來了, 想說再接回KIES去把備份輸回來...

神啊, KIES就是不認我的i9000....

我試可以找到備份起來的檔案...一個.sbu的檔案...
\Documents\samsung\Kies\Backup\GT-I9000\xxxxxxxxxxx.sbu

可是怎解啊?

這位先生寫了一個 program可以把 .sbu裏的聯絡人拉出來成Vcard....
這樣就可以再匯進去手機了

https://www.lord-luncher.de/index.php?pg=2




輸出時會問要不要整成 single file, 選不要....就會有一堆vcard...
再copy到手機的sd card, 就可以用匯入的方法搞定...

留言

張貼留言

這個網誌中的熱門文章

Heltec ESP32+OLED+Lora, hardware testing

圖片
you can easily find some good boards from china, but most of them lack of accurate document... Hrere is an example; https://hackaday.io/project/26991-esp32-board-wifi-lora-32 the board looks good with lora and a 128x64 OLED, but the IIC and reset connection is important, since pin can be muxing easily, so every board could be different. pinMode(16,OUTPUT);  digitalWrite(16, LOW); // set GPIO16 low to reset OLED  delay(50);  digitalWrite(16, HIGH); // while OLED is running, must set GPIO16 to high  and, if needed, edit your Wire.begin() to Wire.begin(4,15); (4 = SDA 15 SCL)  i tested it with the Adafruit SSD1306 and the Acrobotics SSD1306 Librarys  both work.  Display size is 128x64 There are discussions on these boards on TＴＮ as a LORA node..or maybee single ch gateway? Heltec has a git :  https://github.com/Heltec-Aaron-Lee And there is another copy call TTGO https://de.aliexpress.com/item/TTGO-LORA32-868-915-Mhz-SX1276-ESP32-Oled-display-Bluetooth-WIFI
閱讀完整內容

micro SD card for ESP32, on lolin32 with OLED and heltec 32 lora oled

圖片
I have purchased 2 micro SD card holder for my esp project. First I would like to test with heltec esp32 lora oled module. this module uses: sck=05 MISO=19 MOSI=27 SS(lora)=18, then I assigned 21 for sd SS and there is a lib in esp32-arduino, which use SS default at 5 I took the example and use SD.begin(21), but I alway get the error: entry 0x40078a9c Card Mount Failed But I do saw once that it read out the sd card type and volume. Not sure it's the issue of lora sd card swithing, or it just can't work. The other esp32 card I have is an wemos esp32 oled, it did not leave me too much pins, I need to find out how to connect sd to it. But I have wemos D1 mini esp8266 on hand, and connect it as:  * The WeMos Micro SD Shield uses:  * D5, D6, D7, D8, 3V3 and G  *  * The shield uses SPI bus pins:  * D5 = CLK  * D6 = MISO  * D7 = MOSI  * D8 = CS It's not working with the example in the arduino IDE 1.8.5, which marked SD(esp8266), but it w
閱讀完整內容

Install Network Time Protocol(NTP) on BeagleBone with Angstrom linux and set local time zone

Referenced from : http://cwraig.id.au/?p=513 1. Update your Package List opkg update 2. Get the ntp Package opkg install ntp ntpdate Update 2014/07/03 for the latest beaglebone image(2013-06-20) with kernel 3.8.12, after this installation,  system will add to service list, so only need to change time zone 3. Now we need to stop the ntpd service so we can request a manual update /etc/init.d/ntpd stop manual update ntpdate pool.ntp.org type in date, you should see the date is changing to current date and time, but the time zone is not corrected. The time zone info is contained in /etc/localtime , use this to remove it: rm /etc/localtime before link up our time zone, look into /usr/share/zoneinfo folder for your timezone. I did not find taiwan in asia, not plan to use hong_kong, but there is still: /usr/share/zoneinfo/Etc/GMT-8 now we make the link with ln command ln -s /usr/share/zoneinfo/Etc/GMT-8 /etc/localtime now type date again to check, should ha
閱讀完整內容